How to Install Replacement Windows

Installing replacement windows in your home isn’t an over-complicated task to accomplish but it should be given a reasonable amount of time and will require some skill to complete to a reasonable standard. Once you’ve read a little about what’s involved in a full home replacement you should be good to go. Many families will pay several thousand dollars for the installing of their windows; however you will usually be able to do it yourself for as little as around $300 in total, of course this will vary depending on the type and size of the window you’re going to be installing. Bay and bow window configurations are more expensive to install than most others as you would expect, this is mainly due to their size.

There are 4 main steps in the window replacement process and they are:

  • Gathering your tools and materials together
  • Measuring correctly for the replacement window
  • Removing the old windows from the window frame
  • Installing the new window units into the frame


Cross Section of Window

Usually it will take you around 4 hours to replace a large window in full and of course you are going to need several tools to enable you to do the job. Most people have these tools lying around the home and including things like a hammer, screwdriver, chisel, knife, tape measure, square, wood shims, wood putty, caulking tubes, sandpaper, expanding foam and a pry bar. Once you have all of your tools gathered together you will be able to move onto measuring for the installation.



Measuring Up

Measure twice, cut once

It doesn’t matter what type of window you are using the measuring essentials are basically the same from unit to unit. It’s important that this is done right because everything else you do will stem from this.

When you’re undertaking the measuring process you will need to obtain 6 measurements in total, 3 along the horizontal aspect and 3 along the vertical aspect. The height and the width measurements are taken from the window jamb to the window jamb, this basically refers to the inside edge of the window frame. It’s important that along both axis that 3 measurements are taken, one to the left, middle and right when measuring the height and one to the top, middle and bottom when taking measurements for the height. You may see that these measurements are not all the same, if this is the case then you will need to take the smallest height and the smallest width measurement, these will be the dimensions for your new window.


The first thing to be removed will be the window stops, these are the things which hold the window in place within the frame. On older windows it may just be a case of unscrewing them or using a utility knife to cut the edges away and pull them out. You should try not to damage the window stops if possible as these can be reused and save you a little bit of extra money.

The next step should be fairly straightforward now that the window stops have been removed, you will need to remove the window sashes or the window panel, depending on the type of window which is currently installed. Because the stops hold the window in place the sash or pane should just lift out with very little effort.

Finally, you should take out any parting beads to allow you to remove the final part of the window sash, if it’s a casement window you’re removing you will often not have a parting bead in the installation. Now that your window is out you will be able to fill any holes in your window jambs, smooth them out and get them ready for the new windows.


Final touches of installation

The final part of the process is the hardest, installing the new replacement window. The first part of the process will be to lay a bead of caulk along the inside of the outside stops, this is where the replacement windows are finally going to rest against. You can then go ahead and install the first part of the window which will be the window header, this should be installed into the top window jamb.

Next, you will insert the replacement window unit into the square hole and see if it fits into place. If the window doesn’t quite fit because it’s too small then you will need to tap some wood shims into place to make it a tight fit in the window hole. Once the window is fixed well in place you will be able to screw the window onto the jamb so it’s fixed in place.

You can now go ahead and check to see if your replacement window works okay, try opening and closing the main parts of the unit and making sure parts which aren’t meant to move don’t move.

When to Own the Right Tool for the Job

When you’re in the building business, one of the decisions you should make is whether to rent or to purchase your tools. There are advantages and disadvantages to each approach, and you may likewise make your choice, and you consider each tool you need. Making the right choice can spare you a good deal of money after some time, however indiscreet decision making can cost you. Here is the thing that you need to look at when you are deciding on buying and renting that next enormous piece of building tools.

When to Buy Your Building Tools

Buying tools and machinery is a major investment, yet it can likewise spare you money over the long haul. Buying is a good decision when:

• You’ll use the tools frequently. If you burrow a few foundations for homes every month, it most likely makes sense to put resources into that shiny shovel.

• You don’t live close to a rental focus. If it’s a major bother to get the tools you need to take care of business, you’ll lose money or time going to buy machinery.

• You’re hoping to expand. If you’re doing admirably financially and are prepared to take your work to the following level, owning your particular tools with your name and logo as an afterthought likewise pays to publicize shows potential clients you’re the genuine article.

• You can bear to store or maintain new tools. If you as of now have an industrial carport and protection approach that you can include your new tools too, buying will be reasonable. Remember to ascertain shrouded maintenance expenses into your decision also.

When to Rent Your Building Tools

Buying isn’t for everyone, and a cheap rental may make sense in specific circumstances. Renting your building tools is shrewd when:

• You want to test drive. Regardless of the possibility that you’re in a good position to purchase based on the agenda over, it’s as yet an extraordinary thought to rent to take another piece of tools for a spin under genuine work conditions before making your investment.

• You need an additional lift amid the bustling season. In case you could truly use an additional forklift for a couple of months each spring, yet would wind up stopping it for the remaining part of the year, temporary rentals make good budgetary sense. Along these lines, you’re not on the snare for the protection and maintenance year-round.

• You need to keep your costs low. Renting makes it simple to precisely figure the expenses of the tools into your project evaluate, so you aren’t left on the snare for unforeseen maintenance cost on your building tools.

• You can rent from a reliable vendor. Finding a place with good staff to assisting you answer every one of your inquiries concerning rental tools is crucial.


When considering between buying and renting, it’s regularly an issue of when you want to use your money later. Buying enables you to put upfront on a piece of building tools that can spare you money as time goes on, yet renting lets you pay minimal upfront in return for a continuous cost each time you want to utilize the tools. Consider carefully, and you’ll assist your building business develop.

Safe Home renovations

Home renovations can be a bad dream when the temporary worker you’ve contracted all of a sudden understands that revealing a divider likewise uncovered many years of clean and earth. Or, on the other hand pulling up the cover uncovered more than what you were hoping to see. Contractual workers know the dangers in significant home redesigns and know how to function securely. In any case, when you are the one taking every necessary step, you have to know how you can be sheltered also. Here are some DIY wellbeing tips for when you are taking the necessary steps yourself.

DIY Safety

Safety First!

The essential wellbeing gear for DIY home activities and repairs includes ensuring that what you see, inhale, or handle won’t harm you or others.

Head: While it might seem like an easy decision, wearing some insurance on your head will keep any damage to your head. Hard caps are the best security from knocking your head, or if something falls amid your redesign.

Eyes: Protecting your eyes is basic to any DIY home venture or repair. Wood chips, tidy, protection strands, and even shape can fly at you while chipping away at your home. Your eyes can be effortlessly scratched or harmed to the degree that you may end up losing all or part of your vision. Wellbeing glasses are economical however extremely valuable for what they ensure. Discover ones that fit well and shield your eyes even from the sides. Furthermore, no, your ordinary glasses won’t do to secure your eyes!

Lungs: One thing that is effectively overlooked until the point that it is past the point of no return is shielding your lungs from what you may breathe in a while revamping your home. Utilising a saw to cut wood makes a tonne of wood shavings, and whether you are bringing down or setting up drywall, there will be a considerable amount of mortar clean noticeable all around.

Clean that is breathed in from asbestos or fibreglass is another issue totally, says Jim Jones, CEO of Mr House keeper Residential and Commercial Cleaning. For this situation, an excursion to the healing centre is basic and immediately. Tragically, there is no cure for asbestos being breathed in yet specialists may recommend breathing medicines and solution to help with the side effects.

“This is the reason organisations exist where representatives have the gear and preparing to expel these materials securely, Jones proceeded. Working with wood and drywall can be hazardous as a result of the tidy these materials can make. Continuously wear a clean veil to avoid tidy inward breath. Broadened times of taking in the clean will possibly cause lung issues.” Quora.

While an expendable veil that covers your nose and mouth will shield you from particles of tidy and shape, you will need to wear a respirator if you will be working with perilous chemicals. Indeed, even some cleaning operators can be risky when joined, for example, blanch and a smelling salts item.

Ears: Your ears are very touchy, and constant noisy clamour from pneumatic nail firearms, saws, or different apparatuses and hardware you may use in your redesigns could cause hearing misfortune. Wearing delicate, expendable ear fittings will forestall harm to your listening ability.

Hands, Fingers, Body: Wearing gloves that are suited to the sort of work you are doing is additionally vital for shielding you from cuts, consumes, metal shavings, chemicals or solvents. On the off chance that you are additionally going to be evacuating asbestos protection, ground surface, or siding you ought to likewise consider defensive dress. Particularly if you will be creeping around in an old storage room or cellar.

DIY home tasks and repairs ought to dependably incorporate DIY security.

Replacing and Installing a New Exterior Door

It is that time again! Time for another update from us on what we are up to now. If you have been following along this far, then you know that Joe is currently in the middle of remodeling a basement for Sally and Scott. The last time we updated you on what we were doing, Joe brought in Dave and his mold sniffing dog, Sam to make sure there was no mold before we proceeded. It was really fun to watch that happen so we hope to bring them on for more of our projects soon. If, or when, we do, we will tell you all about it!


A lot has happened with the basement remodel since then. Since our last update, the drywall in the basement has been hung, some doors have been installed, and most of the painting has been done. Since I have covered these projects in the past, I am not focusing on them in this update. However, if you want to learn about these things, check out the following links: How to Install Drywall, Installing Pre-Hung Doors, and Painting like a Pro. Now that I added those for you to check out, let’s get on with the update of what we have been doing.

Construction contractors replacing doors

If you are wondering how to install an exterior door, like many of my readers have been asking about, then I am excited to share this new update with you. The old door we have replaced was the original door for this house so it was definitely time for an update on that!


About the New Door

Since the old door was the original one for this house, the new door is a little bigger than the old one. The new door is a simple one though. Nothing too fancy. Just a simple steel door with six panels.

Let’s get on with the steps to install it!


Step One: Remove the Old Door

First things first, of course! Remove the old door by taking it off its hinges and removing the brick molding as well as the door casing. There are a few different layers that go along with removing the old door. These “layers” include the block wall, the pressure treated framing, the blocking and door jamb, and the brick molding, insulation, and of course, the threshold had to be removed too. The door jambs were cut to make them easier to remove, of course. Also, most of the rough framing was saved to reuse with the new door.


After removing the old door and taking the “layers” down that came with it, the old caulking, adhesive, and insulation had to be taken out too. This is an important step to do so you will have a clean frame to add the new door to.


Step Two: The Rough Frame Opening

For the rough frame opening, you will need to glue and nail the 2x4s and the 1x4s in place. In order to make this task an easier one, you should use what Joe and his team used, a Ramset powder actuated nailer. The thing is, if you don’t use one of these tools, you will have to mark and drill the holes for the nails, add the anchors for them, and then screw the boards into their place. So, just make sure you have one of these actuated nailers!



When measuring the rough framing, make sure it measures two inches more than the door in each dimension. You will need this extra space to plumb the door and to level it out.


Step Three: Dry Fit the New Door

Dry fitting means making sure the door will fit before you install it for good. To do this, remove all of the frames for it and set it in there to make sure it will fit your measurements and everything else you have done this far.


The next thing to do is to plane the molding. Although this isn’t really a typical thing to do since most exterior doors are installed with the brick molding facing the block wall. However, this time we installed the new door with the molding flush with the wall. There was actually a good reason for this. They did this because the next bigger and standard sized door wouldn’t fit and also because this was how the old door was installed back in the day.


In a few of the spots, the molding had to be planed to fit. This was accomplished by not only setting the nails just a little bit deeper but also by using a power planer.


Step Four: Glue the Threshold

Once they were satisfied with the fit of the door after dry fitting it, they then had to glue the threshold. They used double beaded adhesive for it by putting it under the door and inside the corners. This is a very important step because doing this will seal out any water that may be near the door on the outside.


Next, they had to check to make sure the door was level and plumb it. Make sure to check each dimension of the door.


To ensure a perfect level of the door, inserting shims is a good idea. You need to place these shims between the door jamb and the rough framing where necessary to ensure a perfect level. These shims will also help the door open and close the way it is supposed to. Joe and his team ended up placing shims behind each of the hinges, at the top of the door itself, and at the latch strike plate.


Step Five: Securing the New Door

Once you are satisfied with the placement of the shims, it is now time to secure the new door in its place. To do this, you will need to place and insert screws behind the weatherstripping to make sure the new door stays in the rough framing like it is supposed to.


Now you might need to trim those shims up after anchoring the door. To do this, score them with your utility knife and then break them where those score lines are.


Step Six: Insulate and Finish with Molding

Now it is time to add the insulation and the molding to finish this out. With this new exterior door, Joe and his team used insulation called, “Great Stuff.”Make sure to put the insulation on the inside and the outside of the door and fill each gap with insulation between the door itself and the frame of it. This “Great Stuff” insulation not only insulates all around the door but will also seal it to keep water out. This is because this insulation they used forms a water resistant seal.

Final Product!

Here is another pro-tip: When insulating, try using a foam that is low pressure because the low pressure foam will keep the door frame from bowing. This type of insulation works well with window frames for the very same reason.


All you need to do now is to add the caulking, to all of the joints and add the molding too. However, this step hasn’t been done by Joe and his guys yet but when it is, I will update this with pictures to show how it is done.